Wilkerson SL2 Bedienungsanleitung PDF herunterladen

Introduction

Follow these instructions when installing, operating, or servicing

the product.

Application Limits

These products are intended for use in general purpose

compressed air systems only.

Operating Pressure Maximum kPa PSIG bar

Bowl w/ Twist Drain / No Sight Gauge 2068 300 21.0

Bowl w/ Twist Drain and Sight Gauge 1700 250 17.0

Operating Temperature Ratings

Metal Bowl w/o Sight Gauge 0°F to 150°F (-18°C to 66°C)

Metal Bowl w/ Sight Gauge 0°F to 150°F (-18°C to 66°C)

Note: Air must be dry enough to avoid ice formation at temperatures below

32°F (0°C).

Symbol

Lubricator

w/ Manual Drain

Installation & Service Instructions:

83-950-000

SL2 Mist Lubricators

ISSUED: May, 2008

Supersedes: August, 2006

Doc.# 83950000, EN# 080328, Rev. 4

Richland, MI 49083 Tel: (269) 629-5000

WARNING

To avoid unpredictable system behavior that can cause personal injury

and property damage:

• Disconnect electrical supply (when necessary) before installation,

servicing, or conversion.

• Disconnectairsupplyanddepressurizeallairlinesconnectedtothis

productbeforeinstallation,servicing,orconversion.

• Operatewithin the manufacturer’s speciedpressure,temperature,

and other conditions listed in these instructions.

• Medium must be moisture-free if ambient temperature is below

freezing.

• Serviceaccordingtoprocedureslistedintheseinstructions.

• Installation, service, and conversion of these products must be

performed by knowledgeable personnel who understand how

pneumatic products are to be applied.

• Afterinstallation,servicing,orconversion,airandelectricalsupplies

(when necessary) should be connected and the producttested for

proper function and leakage. If audible leakage is present, or the

product does not operate properly, do not put into use.

• Warningsandspecicationsontheproductshouldnotbecoveredby

paint,etc.Ifmaskingisnotpossible,contactyourlocalrepresentative

forreplacementlabels.

WARNING

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE

PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS

CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from The Company, its subsidiaries

and authorized distributors provide product and/or system options for further

investigation by users having technical expertise. It is important that you

analyze all aspects of your application, including consequences of any failure

and review the information concerning the product or systems in the current

product catalog. Due to the variety of operating conditions and applications for

these products or systems, the user, through its own analysis and testing, is

solely responsible for making the ﬁnal selection of the products and systems

and assuring that all performance, safety and warning requirements of the

application are met.

The products described herein, including without limitation, product features,

speciﬁcations, designs, availability and pricing, are subject to change by The

Company and its subsidiaries at any time without notice.

EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR INCLUSION

IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE THESE PRODUCTS.

CONTACT YOUR LOCAL REPRESENTATIVE.

Installation

1. The lubricator should be installed with reasonable accessibility

for service whenever possible. Keep pipe or tubing lengths to a

minimum with inside clean and free of dirt and chips. Pipe joint

compound should be used sparingly and applied only to the

male pipe – never into the female port. Do not use PTFE tape

to seal pipe joints – pieces have a tendency to break off and

lodge inside the unit, possibly causing malfunction.

2. Install lubricator so air ﬂows into port labelled “IN” on body.

3. Installation should be upstream of the device it is to lubricate

(valve, cylinders, tool, etc.) as possible.

SafetyGuide

For more complete information on recommended application

guidelines, see the Safety Guide section of Pneumatic Division

catalogs or you can download the PneumaticDivisionSafety

Guide at: www.wilkersoncorp.com

Service Kits Available

Description L10(1/2")

Drip Control Kit PS740N

Sight Gauge Kit SRP-96-026

Bowl Seal F10Y103-2VT

Body

Drip Control

Dome Assembl

Drip Spout

1 2

32°F (0°C) 1
Operation and Service 2

Inhaltsverzeichnis

Seite 1 - 32°F (0°C)

IntroductionFollow these instructions when installing, operating, or servicing the product.Application LimitsThese products are intended for use

Seite 2 - Operation and Service

SL2 Mist Lubricators 83-950-000 By counting the number of drops per minute in the sight dome, you can adjust to your requirements. Every drop visib

Kommentare zu diesen Handbüchern

Keine Kommentare

Wilkerson SL2 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Wilkerson SL2 herunter. Wilkerson SL2 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Wilkerson SL2